Tips to Install a Metal Roof on a House

High performance metal roofs in Ontario are amazing. They last long, are able to withstand some pretty tough weather, and have been used for decades as a cost-effective alternative to traditional asphalt. Installing a metal roof on a house can present some challenges though. For those who wish to install their own metal roof, it’s going to take some work. Once you get the hang of it, we’re sure it won’t seem so complicated.

Get your roof measurement

Prior to buying, get your roof’s measurements so you know how many panels you need to buy. Don’t estimate. Get up there and measure length by width. If there are any questions about how many panels your final measurement equates, speak with a representative.

Follow the instruction manual

Above all else, when you receive your metal roof panels in Ontario, hang onto the manufacturer’s instructions. These are imperative to ensuring your roof is properly installed. When panels have not been interlocked correctly, that could result in leaks.

Attach safety anchors

Follow the instructions and install safety anchors on which you can connect a safety harness. When installing your metal roof, safety should always come first. Most harnesses secure around the chest. Be sure that the harness is properly worn and strapped.

Start at the bottom left or right

When beginning the metal roof installation process, start at either the bottom left or bottom right. Hook the bottom of the metal roof panel to the corner and fasten it securely. Always start in a corner and work your way out from there.

Ensure panels are properly locked

Make sure your panels are properly interlocked and hooked. After the hook is in, you should be able to slide everything into place until it locks. Continue this process with every panel until your reach the edge of the roof.

Cut panels to the appropriate length

If you haven’t received precut metal panels, you will need to use cutters to chop down a panel to the appropriate length to pair it to the edge of the roof. Be sure to speak with your supplier about this. They may recommend an alternative to cutting the panels yourself.

Know that it may take a few days

Getting the panels into place can take a few days so take your time and don’t rush. It’s much more important for every panel to be properly interlocked than it is to get the job done in a fast fashion. To this point, hiring a helper that you trust to work alongside you can help get things done quicker without having to sacrifice quality on the job.

Depending on the features of your roof and what panels need to accommodate in design, there may be other considerations to make. Before you make a purchasing decision, if you’re unsure, speak with your supplier. Post-purchase and before you get started on the roof, be sure that all your tools are good to go, nothing’s malfunctioning or broken, and that all the supplies you need have arrived. Installing a metal roof on a house in Ontario takes a lot of time and labor. All in all, be sure to take it slow, play it smart, and do it right.

How to Re-Roof your House with Metal Roofing

Climate-ready roofing materials like metal are in high demand across Toronto, Ottawa, Chatham, and other communities in Ontario. Among its numerous advantages, metal roofing provides high durability and greater protection to residential and commercial properties.

For homeowners looking to re-roof their home with metal roofing, doing so is a tough but straightforward process. The first step is removing the old roof which in most cases involves traditional asphalt shingle removal and disposal. Note that in many cases this is not necessary and metal roof can be installed directly on shingles. After the old shingles have been fully removed, roofing underlay needs to be spread over the wood of the room to create a new base. There are two methods of installing sheet metal roofing tiles: 1. Direct baking, where no plywood decking is required or 2. Plywood decking or over existing shingle roof. The second method is suitable for the Canadian needs. It allows to install the sheet metal roofing on plywood or over existing shingle roof.

From here, we get to begin fleshing out and getting into the nitty gritty of re-roofing your house with metal roofing. Decide on what side of the house you want to start with. Then, begin screwing in metal sheets into the wood  and through the underlay. With pitched roofs, the installation of tile profile roofing sheets is usually started at the gable, and with hipped roofs always at the hip. Now, repeat this same process on the other side of the house!

The final steps of installing a metal roof starts with placing metal trim along the edges and at the top peak of the roof. Any trim used should be bent to V-shape to fit over the ridge and then, should be screwed down accordingly. All metal trim and bottom sheet should be screwed down.

That’s everything you need to know on how to re-roof your house with metal roofing. Canadian climates, especially in Ontario, are always changing. Metal is an amazing roofing material because it is built to protect. In order to provide property protection though, it needs to be properly installed. Be sure to consult with the manufacturer or supplier of your metal roofing material to identify any additional information to consider related to its installation. We provide installation manual for those who decide to do the work on their own.

This might seem like a tremendous amount of work and we won’t lie – it is. Re-roofing a residential home with metal roofing takes a lot of man-hours. This is why so many Canadians seeking a metal roof end up hiring roofing contractors to complete the installation. Should you decide to hire professional roofing contractors, ensure that they have the experience and knowledge to do the job done right. Be sure to ask what kind of materials they use, what is included in their warranty, and know what is included under their cost estimate.

As the interest in metal roofing continues to rise and more homeowners in Toronto, Ottawa, Chatham, and other Ontario communities choose to re-roof themselves, knowing the safest, most efficient way to do so is important.

How to Avoid Common Mistakes when Installing Metal Roofing

When selecting a metal roofing material and installing the panels on your home, there are many common mistakes that are easily made. Pay close attention to how you install your metal roof panels and be sure to consult this list thoroughly prior to beginning.

Metal Roof Installation

Incorrect Panel Lapping

Installing panels the wrong way is a common mistake that many first-time roofing installers make. Remember, to consult the material supplier on how to install panels correctly. Good suppliers will have video tutorials and printed documentation on installation of their product.

Screwing a Set Incorrectly

Every screw needs to be set correctly. The last thing you want is for them to be too tight or too loose. Always put screws where it is flat in the middle of the panel. If they’re wobbling, check to make sure that your nut driver is in proper working condition.

Don’t use Too Much Sealant

Don’t use sealant or caulk to fix a mistake on your roof. The goal needs to be to waterproof through correct installation and not by covering lazy mistakes with caulk. Any sealant should be a secondary consideration when it comes to waterproofing. When applied, it needs to be under panel or trim where it is protected from the elements because it will last longer there.

Always Measure any Panel Twice prior to Cutting

After a metal roof panel is cut, it can’t be put back together again. The last thing you want to do is measure wrong. Always ensure that you check twice, and then cut. This will keep errors to a minimum at least as it pertains to cutting. Also, ensure you are adequately planning for any penetrations i.e. skylights, attic fans, PVC piping, etc. These require special attention to properly trim and install around these openings.

Assuming Installation is the same for Every Metal Roof

Though some may be similar, always check the instructions prior to installing any metal roof. Depending on the type of panels, special attention may need to be applied to certain areas. Remember, there are varying thicknesses, finishes, and profiles. These factors in addition to the style of the property will be what determines installation.

Over the Edge Paneling is a No-No

Don’t let the metal panel hang over the edge of the roof. Though many may attempt to do otherwise, when you are properly installing a metal roof, it is recommended to ensure paneling only hangs an inch and a half to two inches extending over the edge.

Not enough Screws in your Pipe Flashing

Any penetration in the roof is an area prone to leaking. Pay close attention to how you address penetrations like PVC piping. By only laying in a couple screws and some caulk, that’s not enough to get the job done long-term. The caulk will eventually wear out and then, you’ll have a leak in no time. When installing, ensure sealant is installed underneath the base and that enough screws are placed into the base to keep it in place.

Installing a metal roof is a big project for anyone. Be sure to avoid these common mistakes that have befallen others in the past. Be highly attentive when installing metal roofing as even a minor mistake can require significant re-installation or long-term costs down the line when a leak becomes present.

Latest Trends of DIY Steel Roofing in Ontario

2017 is proving to be a record year for steel roofing. A number of Ontario property owners are choosing steel roof panels over lesser roofing materials, for a wide array of different reasons.

Meanwhile, the province’s home improvement and construction markets have been experiencing high economic growth across the regions of Toronto, Chatham, the GTA, and all across Ontario. Keeping this in mind, the latest trends in DIY steel roofing in Ontario reveal several promising discoveries that show a bright future for steel roofing later this year!

Higher Spending in DIY Home Improvement

According to indicators of home improvement activities in North America, home improvement spending has been experiencing a steady rise year over year throughout the decade.

Today, homeowners are likely to spend more money on roofing than ever before. Though all homeowners are working within budgetary limits, steel roofing is an ideal selection as not only is it not that expensive but the slightly higher front-end investment ensures that your property is equipped with a roof lasting up to 50 years and more!

More Popularity in Energy-Efficient Materials

Property owners in Ontario are searching for ways to recoup their home improvement investments in energy-efficient solutions that will save them on those expensive electricity bills year-round.

Steel roofing is a major draw for this reason. Steel roof panels in Ontario provide on average 25 percent in energy savings, compared to traditional asphalt shingles, making it a very smart choice for anyone concerned with energy efficiency.

Choosing the More Long Lasting, Sustainable Option

Consumers in Ontario are looking towards more sustainable roofing solutions. Made from recyclable materials and providing a long-lasting life span, a homeowner should not have to replace their roof for decades, no matter the weather. Other materials are not as fortunate to be able to offer these advantages. For example, take a couple of heavy Ontario winters back to back, and the wind and ice might be enough to require a partial or full replacement of a traditional asphalt shingle roof.

More Growth in Solar Panels

Every year throughout the past decade, use of solar panels in Ontario has been gradually growing. There is far more growth in the solar panel industry than many have let on. Many homeowners are seeking ways to install solar technology on their roofs, to assist in lowering expensive power bills.

This is where having steel roof panels in Ontario provide benefit. Solar panels need to be attached to a property’s roof and the presence of asphalt shingles can be tough because the installation of these panels oftentimes puncture the shingles. This leaves a property owner with a flawed roofing setup, releasing heat in the winter and potentially causing damage as moisture seeps in.

Steel roofing offers a better surface, guarding against penetration and also lasting twice as long, thereby ensuring homeowners are confident that their solar panels are being properly supported.

DIY Roofing in Ontario is About Adding Value!

So much of 2017’s trends in DIY roofing in Ontario are focused on adding value. That’s one thing that steel roofing does better than any other material. Durable, energy efficient, environmentally friendly, trendy in appearance, and adding on average an increase of up to six percent in value, steel roofing is more than worth the price.

How to Choose the Best Steel Roofing near Me in Ontario

No matter the season in Ontario, any residential roof will take its fair share of abuse over the course of the year. If you’ve made the choice to go with steel roof panels, there is a lot to be said in choosing the best steel roofing material that is most appropriate for your home in Ontario.

Finish/Coating

The first thing you want to evaluate is the type of finish that your steel roof panels have. Many come in a resin-based finish easily applied with a range of different colors and hues. These types of coatings are key in contributing to a roof’s durability and fade resistance. Many people chose steel roofing to avoid the type of staining that is common with granulated-surface shingles.

Valleys

Especially in Ontario, you know a lot of debris is bound to end up hitting your roof. If it does not have a place to go down below, it inevitably gets caught on top of your roof. Tree leaves, pine needles, ice, and snow should have a safe way to travel down your roof through what is called an “open valley”. These types of valleys give a pathway to allow debris and bad things come down from your rooftop and to the ground.

 Warranties

No matter where you are getting your steel roofing in Ontario, you want to ensure that it has an extended warranty. Many companies offer warranties however they can vary in length. Know what you’re buying before you commit to anything and make sure you know who the warranty is from as well. There should be warranties given for the installation workmanship, the product itself, and the integrity of the materials that make up the product.

Ventilation

Steel roofing should come with its own unique ventilation system, allowing air to flow naturally throughout the year. The right amount of ventilation through steel roof panels should help keep a property cool in the summer and maintain a strong, solid performance throughout the winter months.

Any professional roofing contractor should be able to provide you with details on how the ventilation works for a steel roofing product.

Always Consult before Buying

Talk to someone who is experienced with steel roof panel products before making any sort of purchasing decision. There is a large amount of different steel roofs on the market, some far better than others. Consult with someone who knows their stuff and who is able to advise you, after listening to your needs and concerns of course, on the right steel roofing product for your Ontario home.

Get a Roofing Contractor that Knows Steel Roofing

Assuming that most roofers and roofing contractors in Ontario can install steel roofing is a mistake. If the contractor you choose does not have much experience with steel roofing specifically, this could equal to mistakes in the installation that might cost you.

If you are going to hire someone to work on something as valuable as your home, make every effort to ensure that they have the experience required to get the job done right.