How to Avoid Common Mistakes when Installing Metal Roofing

When selecting a metal roofing material and installing the panels on your home, there are many common mistakes that are easily made. Pay close attention to how you install your metal roof panels and be sure to consult this list thoroughly prior to beginning.

Metal Roof Installation

Incorrect Panel Lapping

Installing panels the wrong way is a common mistake that many first-time roofing installers make. Remember, to consult the material supplier on how to install panels correctly. Good suppliers will have video tutorials and printed documentation on installation of their product.

Screwing a Set Incorrectly

Every screw needs to be set correctly. The last thing you want is for them to be too tight or too loose. Always put screws where it is flat in the middle of the panel. If they’re wobbling, check to make sure that your nut driver is in proper working condition.

Don’t use Too Much Sealant

Don’t use sealant or caulk to fix a mistake on your roof. The goal needs to be to waterproof through correct installation and not by covering lazy mistakes with caulk. Any sealant should be a secondary consideration when it comes to waterproofing. When applied, it needs to be under panel or trim where it is protected from the elements because it will last longer there.

Always Measure any Panel Twice prior to Cutting

After a metal roof panel is cut, it can’t be put back together again. The last thing you want to do is measure wrong. Always ensure that you check twice, and then cut. This will keep errors to a minimum at least as it pertains to cutting. Also, ensure you are adequately planning for any penetrations i.e. skylights, attic fans, PVC piping, etc. These require special attention to properly trim and install around these openings.

Assuming Installation is the same for Every Metal Roof

Though some may be similar, always check the instructions prior to installing any metal roof. Depending on the type of panels, special attention may need to be applied to certain areas. Remember, there are varying thicknesses, finishes, and profiles. These factors in addition to the style of the property will be what determines installation.

Over the Edge Paneling is a No-No

Don’t let the metal panel hang over the edge of the roof. Though many may attempt to do otherwise, when you are properly installing a metal roof, it is recommended to ensure paneling only hangs an inch and a half to two inches extending over the edge.

Not enough Screws in your Pipe Flashing

Any penetration in the roof is an area prone to leaking. Pay close attention to how you address penetrations like PVC piping. By only laying in a couple screws and some caulk, that’s not enough to get the job done long-term. The caulk will eventually wear out and then, you’ll have a leak in no time. When installing, ensure sealant is installed underneath the base and that enough screws are placed into the base to keep it in place.

Installing a metal roof is a big project for anyone. Be sure to avoid these common mistakes that have befallen others in the past. Be highly attentive when installing metal roofing as even a minor mistake can require significant re-installation or long-term costs down the line when a leak becomes present.

Latest Trends of DIY Steel Roofing in Ontario

2017 is proving to be a record year for steel roofing. A number of Ontario property owners are choosing steel roof panels over lesser roofing materials, for a wide array of different reasons.

Meanwhile, the province’s home improvement and construction markets have been experiencing high economic growth across the regions of Toronto, Chatham, the GTA, and all across Ontario. Keeping this in mind, the latest trends in DIY steel roofing in Ontario reveal several promising discoveries that show a bright future for steel roofing later this year!

Higher Spending in DIY Home Improvement

According to indicators of home improvement activities in North America, home improvement spending has been experiencing a steady rise year over year throughout the decade.

Today, homeowners are likely to spend more money on roofing than ever before. Though all homeowners are working within budgetary limits, steel roofing is an ideal selection as not only is it not that expensive but the slightly higher front-end investment ensures that your property is equipped with a roof lasting up to 50 years and more!

More Popularity in Energy-Efficient Materials

Property owners in Ontario are searching for ways to recoup their home improvement investments in energy-efficient solutions that will save them on those expensive electricity bills year-round.

Steel roofing is a major draw for this reason. Steel roof panels in Ontario provide on average 25 percent in energy savings, compared to traditional asphalt shingles, making it a very smart choice for anyone concerned with energy efficiency.

Choosing the More Long Lasting, Sustainable Option

Consumers in Ontario are looking towards more sustainable roofing solutions. Made from recyclable materials and providing a long-lasting life span, a homeowner should not have to replace their roof for decades, no matter the weather. Other materials are not as fortunate to be able to offer these advantages. For example, take a couple of heavy Ontario winters back to back, and the wind and ice might be enough to require a partial or full replacement of a traditional asphalt shingle roof.

More Growth in Solar Panels

Every year throughout the past decade, use of solar panels in Ontario has been gradually growing. There is far more growth in the solar panel industry than many have let on. Many homeowners are seeking ways to install solar technology on their roofs, to assist in lowering expensive power bills.

This is where having steel roof panels in Ontario provide benefit. Solar panels need to be attached to a property’s roof and the presence of asphalt shingles can be tough because the installation of these panels oftentimes puncture the shingles. This leaves a property owner with a flawed roofing setup, releasing heat in the winter and potentially causing damage as moisture seeps in.

Steel roofing offers a better surface, guarding against penetration and also lasting twice as long, thereby ensuring homeowners are confident that their solar panels are being properly supported.

DIY Roofing in Ontario is About Adding Value!

So much of 2017’s trends in DIY roofing in Ontario are focused on adding value. That’s one thing that steel roofing does better than any other material. Durable, energy efficient, environmentally friendly, trendy in appearance, and adding on average an increase of up to six percent in value, steel roofing is more than worth the price.

How to Choose the Best Steel Roofing near Me in Ontario

No matter the season in Ontario, any residential roof will take its fair share of abuse over the course of the year. If you’ve made the choice to go with steel roof panels, there is a lot to be said in choosing the best steel roofing material that is most appropriate for your home in Ontario.

Finish/Coating

The first thing you want to evaluate is the type of finish that your steel roof panels have. Many come in a resin-based finish easily applied with a range of different colors and hues. These types of coatings are key in contributing to a roof’s durability and fade resistance. Many people chose steel roofing to avoid the type of staining that is common with granulated-surface shingles.

Valleys

Especially in Ontario, you know a lot of debris is bound to end up hitting your roof. If it does not have a place to go down below, it inevitably gets caught on top of your roof. Tree leaves, pine needles, ice, and snow should have a safe way to travel down your roof through what is called an “open valley”. These types of valleys give a pathway to allow debris and bad things come down from your rooftop and to the ground.

 Warranties

No matter where you are getting your steel roofing in Ontario, you want to ensure that it has an extended warranty. Many companies offer warranties however they can vary in length. Know what you’re buying before you commit to anything and make sure you know who the warranty is from as well. There should be warranties given for the installation workmanship, the product itself, and the integrity of the materials that make up the product.

Ventilation

Steel roofing should come with its own unique ventilation system, allowing air to flow naturally throughout the year. The right amount of ventilation through steel roof panels should help keep a property cool in the summer and maintain a strong, solid performance throughout the winter months.

Any professional roofing contractor should be able to provide you with details on how the ventilation works for a steel roofing product.

Always Consult before Buying

Talk to someone who is experienced with steel roof panel products before making any sort of purchasing decision. There is a large amount of different steel roofs on the market, some far better than others. Consult with someone who knows their stuff and who is able to advise you, after listening to your needs and concerns of course, on the right steel roofing product for your Ontario home.

Get a Roofing Contractor that Knows Steel Roofing

Assuming that most roofers and roofing contractors in Ontario can install steel roofing is a mistake. If the contractor you choose does not have much experience with steel roofing specifically, this could equal to mistakes in the installation that might cost you.

If you are going to hire someone to work on something as valuable as your home, make every effort to ensure that they have the experience required to get the job done right.

Tips For DIY Steel Roofing – Do It Yourself Steel Roof Will Save Money

When it comes to do it yourself steel roofing in Ontario, it is not as easy as it might seem at first. Initially, it may seem as simple as putting up and connecting some panels. The truth is that there’s a lot more intricate work oftentimes lost in DIY steel roofing in Ontario that can result in potentially hundreds of dollars’ worth of damage.

When studying do it yourself steel roofing in Ontario, the best thing to start with is knowing how to prepare. Measure the roof correctly and precisely. Each Ontario steel roofing panel is cut to the exact size required and if panels are too short, you may run into some major expenses down the line. Not knowing the precise measurements of the roof is also going to mean additional work down the road. This is a very common rookie mistake when it comes to do it yourself steel roofing in Ontario. Don’t be caught making that same mistake.

Do It Yourself Steel Roofing Ontario - Eco-Tile

It also bears in mind that any type of Ontario DIY steel roofing installation/repair is highly dangerous and safety should always be maintained as a top priority. Full body harnesses and some sort of fall protection system is highly recommended – potentially including roof anchors, a lifeline, and shock-absorbing lanyard. Any Home Depot, Home Hardware, or Lowe’s should have these ready for purchase. Among the first things you do when beginning on steel roofing in Toronto, steel roofing in Ottawa, or steel roofing in Ontario is to put on the body hardness, have a rope with you, and install the harness prior to doing any measuring work.

If you are new to DIY steel roofing, there are several tools, materials, and supplies that you should have on-hand. These include a carpenter’s hammer or roofing hatchet, a utility knife, a carpenter’s pencil, sheet metal snips, a tape measure, a tool belt, a sheet metal hand seamer and folder, and power tools like a drill or wood cutter. Nails and sealant or caulking also are required in order to perform a steel roofing installation most effectively.

Now we get to the installation. Depending on the exact type of steel roofing selected, the instructions may be different. It is highly important that you do not skip any steps as it relates to the installation and that you get it done right.

Though installing steel roofing can be a daunting task to some, approaching it with an open mind is a very healthy way of getting the job done. If you’re considering installing a steel roof in Ontario, take from the information written here and do your research before getting started.

To many people, the hardest part of the DIY steel roofing process is actually selecting the type of roofing they want. Once the hard part is done, going through the instructions and putting in the work to install it is all pretty straightforward.

Steel roofing is easy to transport and simple to install if one does not take the instructions and preparation process for granted. Don’t take it too hard when you make a mistake because they will happen. As long as they are not too costly, you should be good.

Steel roofs continue to gain in popularity because of their simplicity and economy. Going through the process of installing a steel roof yourself can help save money as well as help to provide a more thorough understanding of a part of your property that oftentimes goes overlooked.